Dings-dynamics-group 80 Series End Mount NEMA 2 HEAVY DUTY Bedienungsanleitung PDF herunterladen

80 Series

4 Post NEMA 2 Enclosure

Brake Instructions

Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself

and others by observing all safety information. Failure to comply with instructions could result in personal injury

and/or property damage! Retain instructions for future reference. When unpacking the brake, inspect it carefully

for damage that may have occurred during transit.

Bulletin No. BK4804 (10/10)

4740 WEST ELECTRIC AVENUE  MILWAUKEE, WI 53219  PHONE 414/672-7830  FAX 414/672-5354  www. dingsbrakes.com

WARNING

Brake performance and features must be carefully matched to the

requirements of the application.

Consideration must be given to torque requirements, especially where

an overhauling condition exists, as well as thermal capacity, ambient

temperature, atmospheric explosion hazards, type of enclosure and any

other unusual conditions.

Improper selection and installation of a brake and/or lack of maintenance

may cause brake failure which could result in damage to property and/or

injury to personnel.

If injury to personnel could be caused by brake failure, additional means

must be provided to insure safety of personnel.

Do not operate manual release or energize brake coil before installation,

in order to preserve prealignment of rotating discs for ease of installation.

DESCRIPTION

This brake is direct acting, electromagnetically released and spring set.

It uses rotating and stationary disc contact to supply positive braking

action. It retains quick release and setting capabilities at all times.

Simplicity of design has reduced maintenance to an absolute minimum.

As with any electromechanical equipment, however, periodic inspection

and adjustment will assure optimum performance. As the friction disc

wears, the magnet gap will increase. The magnet gap should be check

periodically and adjusted when necessary.

SPECIFICATIONS

MOTOR FRAMES - 284TC, 286TC.

HOUSINGS - Cast iron and aluminum.

DUTY - Rated for continuous duty.

VOLTAGES - All standard NEMA voltages and frequencies available.

Other voltages and frequencies are optional.

MOUNTING - Direct to NEMA “C” motor flanges. Adaptors for larger or

smaller frames, foot mounting and vertical mounting are available.

SHAFTS - NEMA standard length motor shafts and thru shafts may be

used on all models except units with Mark II Release (Cover modification

required for thru shafts).

ORDERING INFORMATION

The following data should be furnished with your order for:

REPLACEMENT PARTS

Brake Model Number

Part Number from Tables

Part Description from Tables

(On hub order furnish bore dia. & keyway dimensions. On

electrical parts specify voltage, phase & frequency.)

REPLACEMENT BRAKE

Model Number

Voltage, Phase & Frequency

Hub Bore & Keyway Dimensions

Mounting - Horizontal or Vertical. (If vertical, specify whether above or

below motor. If brake includes foot mounting bracket or adaptor, specify.

)

Figure 1.

Figure 2.Wiring Diagram

G080341-001

1 2 3 4

Inhaltsverzeichnis

Seite 1 - Figure 2.Wiring Diagram

80 Series 4 Post NEMA 2 Enclosure Brake InstructionsRead carefully before attempting to assemble, install, operate or maintain the product described.

Seite 2

INSTALLATION(See Figures 3, 5 & 6, Tables 1, 2 & 3)1. Remove hub (1) from brake and position on motor shaft with key according to dimension “N

Seite 3

2Table 1. Parts ListITEMNO.PCS.REQ’DDESCRIPTION PART NO.1 1 Hub H08003* (4)2 1 Bracket w/studs – 1 disc H080309-0012 1 Bracket w/studs – 2 disc H08030

Seite 4 - TROUBLE SHOOTING

Table 2. DimensionsFigure 5. Outline DrawingTROUBLE SHOOTINGA. IF BRAKE DOES NOT RELEASE:1. Check brake visually for broken or damaged parts.2. Check

Kommentare zu diesen Handbüchern

Keine Kommentare

Dings-dynamics-group 80 Series End Mount NEMA 2 HEAVY DUTY Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Dings-dynamics-group 80 Series End Mount NEMA 2 HEAVY DUTY herunter. Dings Dynamics Group 80 Series End Mount NEMA 2 HEAVY DUTY User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Dings-dynamics-group 80 Series End Mount NEMA 2 HEAVY DUTY