Dings-dynamics-group 70 Series Coupler NEMA 4X Bedienungsanleitung PDF herunterladen

70 Series

Double “C” Face

Washdown Brake Instructions

IMPORTANT

Read carefully before attempting to assemble, install,

operate or maintain the product described. Protect yourself

and others by observing all safety information. Failure to

comply with instructions could result in personal injury

and/or property damage! Retain instructions for future

reference. When unpacking the brake, inspect it carefully

for damage that may have occurred during transit.

Bulletin No. BK4720 (8/11)

4740 WEST ELECTRIC AVENUE MILWAUKEE, WI 53219 PHONE 414/672-7830  FAX 414/672-5354  www. dingsbrakes.com

WARNING

Brake performance and features must be carefully matched to the

requirements of the application.

Consideration must be given to torque requirements, especially where

an overhauling condition exists, as well as thermal capacity, ambient

temperature, atmospheric explosion hazards, type of enclosure and

any other unusual conditions.

Improper selection and installation of a brake and/or lack of mainte-

nance may cause brake failure which could result in damage to prop-

erty and/or injury to personnel.

If injury to personnel could be caused by brake failure, additional

means must be provided to insure safety of personnel.

DESCRIPTION

This brake is direct acting, electromagnetically released and spring set.

It uses rotating and stationary disc contact to supply positive braking

action. It retains quick release and setting capabilities at all times.

Simplicity of design has reduced maintenance to an absolute minimum.

As with any electromechanical equipment, however, periodic inspection

and adjustment will assure optimum performance. As the friction disc

wears, the magnet gap will increase. The magnet gap should be checked

periodically and adjusted when necessary. This brake is offered with a

“NEMA 4X Washdown” housing style.

Figure 1.Wiring Diagram

INSTALLATION

Refer to Figures 1 & 2

Insert key into motor shaft keyway. Key length to be as

shown below for models designated.

Used on all models except

71010, 71015, 72025, and

72035 with 1-1/8” dia. shaft.

For models 71010, 71015,

72025 and 72035 with 1-1/8”

dia. shaft.

Slide brake onto motor shaft, aligning key in motor shaft with

keywayin brake shaft. Secure brake to motor “C” face with four

1/2” socket head capscrews. Connect coil leads per appropriate

diagram.

G070826-001

1 2 3 4

Inhaltsverzeichnis

Seite 1 - G070826-001

70 Series Double “C” Face Washdown Brake InstructionsIMPORTANTRead carefully before attempting to assemble, install, operate or maintain the product

Seite 2 - MAINTENANCE AND SERVICE

MANUAL RELEASE(See Figure 4)To operate release, rotate two nuts (16) clockwise until stopscrew (14) hits pin. Brake will remain in released position u

Seite 3 - WARRANTY

MAGNET COIL REPLACEMENT(See Figures 1, 3 & 4)Remove magnet assembly as outlined under FRICTION DISCREPLACEMENT.Coils (21) are held in place with e

Seite 4 - 4740 WEST ELECTRIC AVENUE

Table 2. Parts List* Number of rotating discs is shown in model number. Example:6-72025-38 has two rotating discs.Also see Table 1 for number of frict

Kommentare zu diesen Handbüchern

Keine Kommentare

Dings-dynamics-group 70 Series Coupler NEMA 4X Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Dings-dynamics-group 70 Series Coupler NEMA 4X herunter. Dings Dynamics Group 70 Series Coupler NEMA 4X User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Dings-dynamics-group 70 Series Coupler NEMA 4X